{"product_id":"netafim-techline-tlell-17mm-90-insert-elbow-for-drip-irrigation","title":"Netafim Techline TLELL 17mm 90° Insert Elbow for Drip Irrigation","description":"\u003cp\u003eTurn a 17mm Netafim Techline dripline around a 90° corner without kinking the tubing and without a clamp. The TLELL is the OEM Netafim insert elbow for Techline tubing — barbed inserts on both legs, one-piece molded body, push the cut ends of the dripline onto the barbs and the corner is built. Designed specifically for the 0.56″–0.60″ ID range that Netafim’s 17mm Techline runs in, so the seal is dialed in for that exact tubing.\u003c\/p\u003e\u003ch3\u003eWhy Netafim Is the Right Match\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eOEM Netafim — the same brand as your Techline dripline, so the barb-to-ID fit is engineered, not approximated\u003c\/li\u003e\n\u003cli\u003e17mm sized for Netafim Techline HCVXR, HCVXR-RW\/RWP, CV, DL, and RW\/RWP driplines, plus generic 17mm PE irrigation hose in the 0.56–0.60″ ID range\u003c\/li\u003e\n\u003cli\u003e90° turn — routes the dripline around corners cleanly without trying to bend the tubing past its kink radius\u003c\/li\u003e\n\u003cli\u003eTool-free installation — no clamps, no glue, no tools required\u003c\/li\u003e\n\u003cli\u003eUV resistant — survives direct sun and the chemistry of irrigation water\u003c\/li\u003e\n\u003cli\u003eOne-piece construction — no joints, no glued seams, nothing to come apart underground in year five\u003c\/li\u003e\n\u003cli\u003eNETAFIM molded into the body for easy on-site identification during service calls\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhere It Shines\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eRouting 17mm Techline around the corners of garden beds, raised planters, or hardscape\u003c\/li\u003e\n\u003cli\u003eTurning the dripline from a horizontal supply run up a fence post or wall to feed hanging planters\u003c\/li\u003e\n\u003cli\u003eTight-radius corners where a kinked tubing run would restrict flow downstream\u003c\/li\u003e\n\u003cli\u003eService-call patches replacing a kinked or damaged elbow section\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModel: TLELL\u003c\/li\u003e\n\u003cli\u003eSizing: 17mm — fits 0.56″ to 0.60″ inside diameter dripline\u003c\/li\u003e\n\u003cli\u003eCompatible with: Netafim Techline HCVXR, HCVXR-RW\/RWP, CV, DL, RW\/RWP, and 17mm PE irrigation hose in the 0.56–0.60″ ID range\u003c\/li\u003e\n\u003cli\u003eGeometry: 90° elbow (two-port)\u003c\/li\u003e\n\u003cli\u003eConnection: Barbed insert — tool-free push-fit, no clamps required\u003c\/li\u003e\n\u003cli\u003eMaximum pressure: 50 psi\u003c\/li\u003e\n\u003cli\u003eConstruction: One-piece molded plastic, UV-resistant\u003c\/li\u003e\n\u003cli\u003eUse: Buried or surface, residential \/ commercial drip irrigation\u003c\/li\u003e\n\u003cli\u003eApproximate weight: 1 lb per pack\u003c\/li\u003e\n\u003cli\u003eOrigin: Netafim\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eInstall Notes\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eCut the dripline square with a sharp knife or PE pipe cutter (a ragged cut won’t seal)\u003c\/li\u003e\n\u003cli\u003ePush each tubing end onto a barb fully — the last barb ridge should be inside the tubing\u003c\/li\u003e\n\u003cli\u003eNo clamp required — the barb design seals against the dripline ID once the tubing is fully home\u003c\/li\u003e\n\u003cli\u003eKeep system pressure under 50 psi — the Techline family is low-pressure dripline, not a poly mainline\u003c\/li\u003e\n\u003cli\u003ePressure-test before backfilling the trench\u003c\/li\u003e\n\u003cli\u003eShut the zone off at the valve before cutting into a pressurized line\u003c\/li\u003e\n\u003cli\u003eFor 12mm Techline EZ — this is the wrong size; use Netafim Model T12ELL instead\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003ePair With\u003c\/h3\u003e\u003cp\u003eFor inline splices in 17mm Techline, use the Netafim \u003cstrong\u003eTLCOUP\u003c\/strong\u003e insert coupling. For tee\/branch connections, the \u003cstrong\u003eTLTEE\u003c\/strong\u003e. For threaded transitions to 1\/2″ or 3\/4″ MPT supply, the \u003cstrong\u003eTL050MA\u003c\/strong\u003e or \u003cstrong\u003eTL075MA\u003c\/strong\u003e adapters.\u003c\/p\u003e\u003cp\u003eStop by Garoppo’s for the count you need, or order ahead for the next install.\u003c\/p\u003e","brand":"Drip Works","offers":[{"title":"Default Title","offer_id":54139882963236,"sku":"50909","price":0.68,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0968\/5322\/9860\/files\/netafim-techline-tlell-17mm-insert-elbow-angled_e38d3606-3d7b-40af-914b-1d8e47395a66.png?v=1780338099","url":"https:\/\/garoppos.com\/products\/netafim-techline-tlell-17mm-90-insert-elbow-for-drip-irrigation","provider":"Garoppo's Stone \u0026 Garden Center and Feed \u0026 Pet Supply","version":"1.0","type":"link"}