Add traction to a sealed pool deck or walkway without changing how it looks. SRW Products Inc. SR Slip-Resist Sealer Additive 3.2 oz is a pouch of fine polypropylene aggregate that you stir into the second coat of an SRW film-forming sealer. It suspends in the sealer, rolls on with it and dries invisible, leaving a lightly textured surface that gives wet feet something to grip. One 3.2 oz pouch treats one gallon of sealer, so a quick calculation from your sealer coverage tells you how many to buy.
Key Features
-
Invisible grip: The polypropylene aggregate is not visible once the sealer dries, so the gloss or satin finish you chose stays the same.
-
Built for wet areas: Improves slip resistance around pools, on steps and in any high-traffic zone where a film-forming sealer can get slick.
-
1:1 mix ratio: One 3.2 oz pouch per 1 gallon of sealer, added to the second coat only.
-
Works with SRW sealers: Compatible with Specialty Seal PRX; Paver Seal LG and HG; and Premium Seal DG, DG VOC, LGX, LGX VOC, HGX and HGX VOC.
-
About SRW Products: SRW Products makes a full system of paver sealers, cleaners, polymeric sands and hardscape accessories for contractors and homeowners.
How to Use It
Seal the area with your chosen SRW film-forming sealer alone and let that first coat dry for at least 4 hours so it skins over. Before the second coat, empty one pouch into one gallon of sealer and mix until the aggregate is spread evenly through the can. Apply the second coat with a roller only; a sprayer will clog and will not distribute the additive. Stir the mix every 2 to 3 minutes while you work so the aggregate stays suspended rather than settling to the bottom. Follow the sealer’s own instructions for drying and cure time before opening the surface to foot traffic or furniture.
Specifications
- Size: 3.2 oz (0.09 kg) pouch
- Material: polypropylene slip-resistant aggregate
- Mix ratio: 1 pouch per 1 gallon of sealer, second coat only
- Application: roller only; do not spray once added
- Compatible sealers: Specialty Seal PRX; Paver Seal LG, HG; Premium Seal DG, DG VOC, LGX, LGX VOC, HGX, HGX VOC
- Part number: SSSR PG; 12 pouches per carton
Stop by Garoppo’s Stone & Garden Center and Feed & Pet Supply to see it in person and pick one up, or schedule local delivery within our service area.
SRW Products SR Slip-Resist, part SSSR PG, 3.2 oz (0.09 kg) pouch, 12 per carton. Polypropylene slip-resistant aggregate for SRW film-forming sealers. Dosed 1:1, one pouch per gallon, in the second coat only. Dries invisible; the sheen of the base sealer is unchanged. Specify on pool decks, steps, entries and any high-traffic surface where a film-forming sealer would otherwise be slick when wet. Compatible with Specialty Seal PRX; Paver Seal LG and HG; Premium Seal DG, DG VOC, LGX, LGX VOC, HGX and HGX VOC.
Key Features
- Aggregate: Polypropylene. Suspends in solvent and water-based SRW film-formers on the list above; not for penetrating sealers.
- Dose: 1 pouch per gallon of second-coat sealer. Pouch count equals second-coat gallons.
- Appearance: Invisible when dry. No change to gloss, satin or wet-look finish.
- Application: Roller only. Sprayers will not carry the aggregate and will clog.
- Packaging: 3.2 oz pouch; 12 pouches per carton for stocking trucks.
Installation
- First coat: Apply the selected film-forming sealer plain. Allow a minimum 4 hours to skin over before the second coat.
- Mix: Add one pouch to one gallon of sealer immediately before the second coat and mix until the aggregate is uniform through the whole gallon.
- Second coat: Roll only. Stir every 2 to 3 minutes during application to keep the aggregate suspended; a settled can puts all the grit on the last 50 sq ft.
- Cure: Follow the sealer's dry and cure schedule before traffic.
Spec Notes
Treat the additive as part of the sealer take-off rather than a separate line: figure second-coat gallons from the sealer's coverage rate for the substrate, then match pouches one to one. On a pool deck where only the wet perimeter needs traction, mask and roll the additive coat on that zone; the invisible finish means the boundary does not show. The pouch was formerly sold as SR Paver Grip, and the attached MSDS carries that name. Do not add the aggregate to penetrating or non-SRW sealers; the compatibility list is the spec. Store shipping weight 1.1 lb; sold per pouch, 12 pouches to a carton for truck stock.
Specifications
- Size: 3.2 oz (0.09 kg) pouch.
- Ratio: 1 pouch : 1 gallon sealer, second coat.
- Method: Roller only.
- Compatible: Specialty Seal PRX; Paver Seal LG, HG; Premium Seal DG, DG VOC, LGX, LGX VOC, HGX, HGX VOC.
- Part: SSSR PG; 12 per carton. Sold per pouch.
